Load cell connectivity – Ascell Sensor

DSC Digital Load Cell Converter

Ascell Sensor — Mon, 23 Mar 2020 16:43:22 +0000

The digital load cell converter module is designed for use with strain gauge sensors such as pressure transducers, load cells and torque sensors, the DSC offers high speed, high precision strain gauge signal conversion capabilities with linearization and temperature compensation of the sensor.

Features:

Strain gauge to RS232, RS485 or CAN digital load cell conditioning card OEM PCB format for easy fitting to products Ultra high performance, resolution of 1 part in 200,000 (18bit) High speed, up to 500 updates per second Auto calibration or direct entry of mV/V with linearisation Programmable dynamic filter Temperature compensation Error reporting including strain gauge fault conditions and overloads Peak and trough (valley) recording Remote shunt calibration by software command or digital input Free software enabling 24 DSC or DCells to be viewed and logged simultaneously

DATA SHEET

DSCUSB Digital Converter Load cells to USB

Ascell Sensor — Mon, 23 Mar 2020 16:42:44 +0000

The DSCUSB strain gauge to USB converter is a compact, high performance strain gauge digital signal conditioner with USB connectivity aimed at applications which require high-accuracy measurement repeatability. A rugged ABS IP50 enclosure makes this USB load cell converter suitable for all environments. Simply by plugging the DSCUSB into a PC, data can be extracted from most strain gauge bridge input sensors and acquired by software which allows data manipulation removing the need for amplifiers, filters & multimeters. No additional power supply is required as the power is drawn from the USB bus.

Features:

High stability providing superior performance USB strain gauge interface – device appears as a virtual com port Simple & easy to connect to your strain gauge sensor Multiple devices can be used with one PC Supplied with 1.5m USB to Micro USB lead Free DSCUSB strain gauge to USB converter toolkit software Compatible with most load cells and sensors Non-expert maintenance Windows driver DLL’s available OEM pcb versions available

DATA SHEET

ICA MiniAmplifier 4-20mA / 0-10V

Ascell Sensor — Mon, 23 Mar 2020 16:41:51 +0000

The ICA range of miniature strain gauge amplifier offer a high performance strain gauge amplifier in miniature OEM format, designed specifically for fitting inside load cells, converts load cell to 4-20 mA & 0-10 V output. The ICA family offers high stability and fast response. The miniature strain gauge amplifier is available in 6 versions, ICA1H, 2H, 3H, 4H & 6H with high performance and ICA5S with industrial stability. The ICAH range offer very low drift over wide operating temperatures.

Features:

Fits inside sensors, 19.5 mm diameter, 7.6 mm height Outputs of 4-20 mA, 0-10 V, 0-5 V, ±10 V Non interaction between the trimmers makes calibration fast and easy High speed 1000 Hz User selectable span resistor 2 wire 4-20 mA load cell option Robust design, of high noise immunity & reverse polarity protected

DATA SHEET

SGA Load cell amplifier 0-20mA, 4-20 mA, 0-10 V, 0-5 V, ±5 V o ±10 V

Ascell Sensor — Mon, 23 Mar 2020 16:40:56 +0000

The strain gauge amplifier is a high performance signal conditioner for single or multiple strain gauge bridge sensors such as load, force, pressure and torque. The SGA A&D provides strain gauge signal conditioning for load cells and offers a wide bandwidth and a wide input signal range. The device can be powered from AC or DC supplies providing excitation for up to four x 350 Ohm strain gauge bridges. The conditioned output signal can be selected from 0-20 mA, 4-20 mA, 0-10 V, 0-5 V, ±5 V or ±10 V. Options include: Isolated DC supply and DIN rail mount.

Features:

Strain gauge amplifier ideal for load cell signal conditioning Bridge excitation of 10 V DC with drive for four 350 Ohm load cells Conditioned output signal can be selected from 0-20 mA, 4-20 mA, 0-10 V, 0-5 V, ±5 V or ±10 V 1 - 5 kHz adjusted filter for test & measurement applications Selectable sensitivity from 0.1 to 30 mV/V using switches and fine trim potentiometer Switch selectable offset ±70% FS using switches and fine trim potentiometer User selectable analogue output in standard voltage or current format The SGA A&D (shown in main photo) comes complete with case, with option of DIN rail mounted case (D4) as shown on left

DATA SHEET

T24-RM1 Wireless Receiver with Relay Output

Ascell Sensor — Mon, 23 Mar 2020 16:40:08 +0000

This wireless receiver with relay output offers dual power relays capable of mains power switching. Each relay can be configured as high, low or window alarms and can be associated with a group of up to eight T24 transmitters. Relays can operate when the sum of the assigned transmitter modules reach a setpoint or when any of the modules reach the setpoint. There is also a mode where the difference between the lowest and highest value is compared to the setpoint. The T24-RM1 is ideal for applications where you are looking for a group of weights to be within a certain band. i.e. balancing four corners of a weigh scale or a hanging truss.

Features:

Accepts up to 16 inputs from T24 wireless transmitters and triggers a range of selectable output actions Relay operation modes (triggering based on sum of modules, any individual module or difference between low and high values of modules) 2 x 240 Vac 5 A relay module for control & alarms for T24 transmitters Configurable latching, inversion and hysteresis Wide operating supply range Surface mounting enclosure Simple wireless configuration and calibration Internal antenna delivers up to 800 m (2,600 ft) range Sealed to IP67

DATA SHEET

T24-A01 Wireless Receiver with Analogue Output

Ascell Sensor — Mon, 23 Mar 2020 16:39:12 +0000

The Wireless Receiver with Analogue Output provides a configurable analog output for a single T24 wireless transmitter module. The output can be selected from the pre-calibrated voltage and current ranges of 0-10 Volts, ±10 Volts, 0-5 Volts, ±5 Volts, 0-20 mA and 4-20 mA.

Features:

Provides an analogue output from a T24 wireless transmitter Wireless range of up to 800 m (2,600 ft) for the T24-AO1i industrial version & up to 100 m (330 ft) for the T24-AO1 desktop version Configurable analog outputs of 0-10 V, 0-5 V, 4-20 mA, 0-20 mA, ±10 V, ±5 V Update rate of up to 2000 per second Simple wireless configuration and calibration

DATA SHEET

T24-GW1 Wireless Telemetry Modbus Gateway

Ascell Sensor — Mon, 23 Mar 2020 16:31:44 +0000

The T24-GW1 is a wireless Modbus gateway that provides a simple interface for users to gather data from up to 100 transmitters in a T24 network. The T24-GW1 uses either the standard Modbus interface RTU* protocol or a simple ASCII protocol.

Features:

Modbus RTU or ASCII interface (RS232/RS485) Gathers data from up to 100 transmitters Stores data which can be requested by a Modbus system Quick and easy to install Wireless configuration Licence free 2.4 GHz radio Wireless range of up to 800 m (2,600 ft) External power supply (9-32 Volts) Waterproof to IP67

DATA SHEET

T24-Bsu Wireless Telemetry USB Base Station

Ascell Sensor — Mon, 23 Mar 2020 16:30:24 +0000

The Wireless Telemetry USB Base Station - T24-BSu is required for the configuration of all T24 modules and is greatly simplified by the free T24 Toolkit software for Windows supplied upon purchase. Data can also be captured by the wireless telemetry base station (T24-BSu) from an unlimited number of T24 transmitter modules to provide a wireless data logger.

Features:

Provides wireless data from T24 transmitter modules Configures any T24 Telemetry module via USB Powered from USB Wireless range of up to 500 m (1,640 ft) Miniature desktop or wall mount IP50 enclosure 100 Channel logging and mapping software allows viewing of data from T24-SA, T24-VA or T24-IA and offers the ability to log to a CSV file

DATA SHEET

X24-HD Handheld Telemetry Display ATEX / IECEx

Ascell Sensor — Fri, 20 Mar 2020 15:12:38 +0000

The X24-HD is a highly configurable ATEX / IECEx handheld display capable of working with X24 or T24 Transmitter modules. This allows wireless remote viewing of various remote inputs.

Features:

Approved for use in explosive atmospheres Zone 1, Zone 2 Long battery life: 50 days at 12 sessions of 5 minutes per day; 54 hours continuous User controlled backlight 800m range Compatible with cased X24 transmitter, OEM module X24-SAe and T24 transmitters Indication of remote errors. Overload indication and alarm Uses readily available Energizer L91 batteries Sealed to IP67 in a robust handheld enclosure Simple operator interface Assign names to transmitters Tare/Zero/Gross functions Operating temperature range of -10°C to +50°C

DATA SHEET

X24-ACMI Wireless transmitter for load cells ATEX / IECEx

Ascell Sensor — Fri, 20 Mar 2020 15:09:34 +0000

ATEX / IECEx telemetry transmitter module measures strain input and periodically transmits data for receipt by X24 or T24 receivers. High accuracy ratio-metric input allows for calibration and linearisation for pressure, force, torque and weight measurement in explosive atmospheres. Housed in an environmentally sealed IP67 enclosure with battery holder for two Lithium Energiser L91 AA batteries.

Features:

Approved for use in explosive atmospheres Zone 1, Zone 2 800 m (½ mile) range Long battery life: 2 years at 12 sessions of 5 minutes per day; 30 days continuous High accuracy, extremely low temperature drift Up to 4 load cells 4 of 350 Ohms Up to 200 Hz transmission rates Compatible with X24 receiver and T24 receivers OEM option available with X24-SAe module IP67

DATA SHEET